public:lemmon:minnesota_60:cold_start_power_up_sequence
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
public:lemmon:minnesota_60:cold_start_power_up_sequence [2019/04/22 16:32] davner |
public:lemmon:minnesota_60:cold_start_power_up_sequence [2019/05/09 11:10] (current) davner ↷ Page moved from public:minnesota_60:cold_start_power_up_sequence to public:lemmon:minnesota_60:cold_start_power_up_sequence |
||
|---|---|---|---|
| Line 4: | Line 4: | ||
| //Procedure for coming out of lightning shutdown or checking out the telescope and instrument.// | //Procedure for coming out of lightning shutdown or checking out the telescope and instrument.// | ||
| ---- | ---- | ||
| - | =====Dome===== | + | =====Dome |
| - Dome encoder cable over entry door | - Dome encoder cable over entry door | ||
| ===West side of blue yoke, declination axis=== | ===West side of blue yoke, declination axis=== | ||
| - | - dec encoder | + | - Dec encoder |
| - | - dec motor | + | - Dec motor |
| - | - dec tac | + | - Dec tac |
| ===West side of base flange=== | ===West side of base flange=== | ||
| - Finder scope lamp power (for reticle) | - Finder scope lamp power (for reticle) | ||
| Line 48: | Line 48: | ||
| =====Control Room===== | =====Control Room===== | ||
| ===Backside of blue control rack=== | ===Backside of blue control rack=== | ||
| - | Bottom of rack | + | - Bottom of rack |
| - | - #5 TTL mono dome | + | - #5 TTL mono dome |
| - | - #3 stepper motor control | + | - #3 stepper motor control |
| - | - #2 computer manual to dome and telescope control | + | - #2 computer manual to dome and telescope control |
| - | - #1 single paddle control to old paddle | + | - #1 single paddle control to old paddle |
| - | FORTH computer backside | + | |
| - | - //NOTE: If 2MASS is on the telescope there is nothing to disconnect. If another instrument is on the telescope then disconnect Com2 cable.// | + | - //NOTE: If 2MASS is on the telescope there is nothing to disconnect. If another instrument is on the telescope then disconnect Com2 cable.// |
| - | Silver outlet box | + | |
| - | - Bus BNC | + | - Bus BNC |
| - | - Power supply cable | + | - Power supply cable |
| - | - Power supply cable | + | - Power supply cable |
| - | Backside of Rack #1 | + | ===Backside of rack #1=== |
| - PC splitter box | - PC splitter box | ||
| - "From dome" silver cable | - "From dome" silver cable | ||
| Line 72: | Line 72: | ||
| - Large round connector cable | - Large round connector cable | ||
| - Transducer BNC | - Transducer BNC | ||
| + | ===Backside of rack #2=== | ||
| + | - RA motor round connector | ||
| + | - Temperature sensor square gray plug | ||
| + | - //NOTE: Easy to miss// | ||
| + | ===Backside of rack #3=== | ||
| + | - DEC motor cable | ||
| + | - Master Control Panel backside | ||
| + | - Slew SW BNC far left | ||
| + | - J12 under cccc to the right | ||
| + | - Telescope drive control backside | ||
| + | - Limit cable p8 | ||
| + | - #5 TDC cable | ||
| + | - Tilt meter cable | ||
| + | - //NOTE: Easy to miss, just under DEC preamp// | ||
| + | - #5 DEC preamp | ||
| + | - #7 RA preamp | ||
| + | ===Front of blue control panel=== | ||
| + | - Ribbon cable from port 5 to 5 | ||
| + | ===Front of rack #1=== | ||
| + | - Microphone connection for dome | ||
| + | ===Behind control console=== | ||
| + | - Plug two calbes running into ceiling | ||
| + | - Plug power strip and UPS laying on the floor into the wall outlet | ||
| + | - Plug two ethernets | ||
| + | |||
| + | ---- | ||
| + | =====Dome Part 2===== | ||
| + | ===2MASS=== | ||
| + | - Plug in UPS into wall outlet. | ||
| + | - Turn on UPS. | ||
| + | - Plug in orange extension cord into UPS | ||
| + | - Remove the cover form temperature control port. | ||
| + | - While wearing a grounding strap, connect temperature controller cable. | ||
| + | - Plug in temperature controller unit into UPS. | ||
| + | - //NOTE: Sits on blue rack// | ||
| + | - Plug in the Controller square gray power supply into power strip at base of telescope. | ||
| + | - Plug in the IR Camera Power silver box into power strip at base of telescope. | ||
| + | - Turn on Controller power supply | ||
| + | - Turn on IR Camera power supply | ||
| + | |||
| + | ---- | ||
| + | ===Follow the instructions in the black binder to finish setup.=== | ||
public/lemmon/minnesota_60/cold_start_power_up_sequence.1555975948.txt.gz · Last modified: 2019/04/22 16:32 by davner
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
