MOON

User Tools

Site Tools

Trace:
vatt:vatt_lightning_startup_checklist

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
vatt:vatt_lightning_startup_checklist [2021/07/09 21:54]
paul 		vatt:vatt_lightning_startup_checklist [2022/02/20 05:18] (current)
paul
Line 11: Line 11:
 | | | | | | | |
 | ^These actions take place on VATT's building level 1 | | | ^These actions take place on VATT's building level 1 | |
-|Loading dock |Plug the 4kVA UPS input 220V plug into the wall receptacle | | 
 |Loading dock |Plug the 4kVA UPS output 220V plug into the receptacle in the rear of the UPS | | |Loading dock |Plug the 4kVA UPS output 220V plug into the receptacle in the rear of the UPS | |
 +|Loading dock |Plug the 4kVA UPS input 220V plug into the wall receptacle | |
 |Telecom room |Close (turn on) the 100A breaker in ''Panel A'' (the triple breaker is labeled ''Panel C'') | | |Telecom room |Close (turn on) the 100A breaker in ''Panel A'' (the triple breaker is labeled ''Panel C'') | |
-|Loading dock |Turn on the 4kVA UPS turning the key on the front panel. Check that it is ''Ready'' and probably ''Charging'' | |+|Loading dock |Turn on the 4kVA UPS unit, turning the key on the front panel. Check that it is ''Ready'' and probably ''Charging'' | |
 | | | | | | | |
 | ^These actions take place back on the VATT's building level 2 | | | ^These actions take place back on the VATT's building level 2 | |
 |Instrument room |Power up the two UPS units at the bottom of the right rack by holding down the power button on each until an audible signal (beep) is heard, then release the button | | |Instrument room |Power up the two UPS units at the bottom of the right rack by holding down the power button on each until an audible signal (beep) is heard, then release the button | |
 |Instrument room |After the fans have finished spinning up, press the power button on the KVM auxiliary monitor (above the ''vattarchive'' server). ⇓ | | |Instrument room |After the fans have finished spinning up, press the power button on the KVM auxiliary monitor (above the ''vattarchive'' server). ⇓ | |
-|::: |After ''FREE'' flag is displayed, indicating the KVM is finished booting, press the ''Page Down'' key (empty server-selector window will appear) |::: | +|::: |After ''FREE'' flag is displayed, indicating the KVM is finished booting, press the ''PrScr'' key (empty server-selector window will appear) |::: | 
-|Instrument room |Power up ''vattdata'': Momentarily press down the power button | |+|Instrument room |Power up ''vattdata'': Momentarily press down the power button. (There are three LEDs on the right of the server front panel. The top one is amber, the lower two are off. The top one is also the power button. Release the top one when it turns green.) | |
 |::: |KVM: ''vattdata'' should appear in the server-selector; its indicator should turn green |::: | |::: |KVM: ''vattdata'' should appear in the server-selector; its indicator should turn green |::: |
 |::: |More help on the KVM is available in [[vatt:miscellaneous_tips|Miscellaneous Tips]] |::: | |::: |More help on the KVM is available in [[vatt:miscellaneous_tips|Miscellaneous Tips]] |::: |
Line 36: Line 36:
 | | | | | | | |
 ^ ^Proceed to the [[vatt:vatt_warm_startup_checklist|]] ^ | ^ ^Proceed to the [[vatt:vatt_warm_startup_checklist|]] ^ |
 +| ^Do not forget to take the dome short out :!: | |
vatt/vatt_lightning_startup_checklist.1625892862.txt.gz · Last modified: 2021/07/09 21:54 by paul

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki