tcs:tcsng_command_list
This is an old revision of the document!
Table of Contents
TCSng Commands
This is the most comprehensive list to date of the TCSng requests and commands.
Requests
ALL Bulk information Args: N/A Returns: [MOT] [RA] [DEC] [HA] [UT] [ALT] [AZ] [SECZ] [Epoch] MOT = (see MOTION) RA(Right Assention) = HH:MM:SS.ss DEC(Declination) = +DD:MM:SS.ss HA(Hour Angle) = HH:MM:SS UT(Universal Time) = HH:MM:SS ALT(Elevation) = XXX.xx AZ(Azmouth) = XXX.xx SECZ(airmass) = XX.xx EPOCH = EEEE.e
AZ Azimuth
Args: N/A
Returns: [ddd.dd]
BEAM Chop/Nod info for chopping secondary Args: N/A Returns: ???
CORRECTIONS String describing what corrections and rates are enabled/disabled Args: N/A Returns: MPNARFp+tob M=Proper Motion P=Precession N=Nutation A=Aberration R=Refraction F=Flexure p=Parallax +=pointing model used... can change to a,b,c,d? t=Sidereal o=Object b=Bias If disabled, character will be replaced by "_"
DATE date based on UT Args: N/A Returns: [MM/DD/YYYY]
DEC Declination Args: N/A Returns [ddmmss.ss]
DISABLE Output state Args: N/A Returns: 1 for disabled, 0 for enabled
DISEPOCH Current Epoch Args: N/A Returns: XXXX.x
EL Elevation Args: N/A Returns: [ddd.dd]
EQ Equinox Args: N/A Returns: XXXXX.x
HA Hour Angle Args: N/A Returns: [dd:mm:ss]
JD Julian Date Args: N/A Returns: [JJJJJJJ.j]
FLEXFILE Path and file name of current flex map Added by Scott 12/2012
Args: N/A
Returns: [PATH/][pctcs_.tp]
LIMITPROF Horizon limit profile as a function of azimuth Added by Scott 12/2012
The first (and last) value given is the horizon limit at 0 degrees azimuth
each subsequent value is a horizon limit at increments of 15 degrees of azimuth
so the 2nd value is the limit at 15 degrees azimuth, the third is the horizon limit
at 30 degrees azimuth etc.
Args: N/A
Returns [hh] [hh] [hh] [hh] ... (25 in all)
LIMIT limit status bits (ACCORDING TO JAVA GUI) Args: N/A Returns: this returns an 8 bit integer whose bits represent the following bit0(LSB) = RA bit1 = DEC bit2 = Derotator bit3 = Hardware Horizon bit4 = Software Horizon bit5 = Focus Upper bit6 = Focus Lower a 1 indicates limit active, 0 indicates limit not active
LIMIT limit status bits (ACCORDING TO ERIC CHRISTIENSEN)
Args: N/A
Returns: this returns an 8 bit integer whose bits represent the following
bit0(LSB) = RA/HA limit
bit1 = DEC limit
bit2 = derot.
bit3 = hor. hard limit
bit4 = hor. soft limit
bit5 = focus lo limit?
bit6 = focus hi limit?
a 1 indicates limit active, 0 indicates limit not active
LIMITINHIBIT limit inhibit status
args N/A
Returns: 0 if limits are active and 1 if limits are inactive
SOFTLIMITS
S1 and S2 limits are defined here
SOFTLIMITS Software limit status
args N/A
Returns : 6 bit software limit status
bit 0 = RA S2
bit 1 = RA S1
bit 2 = DEC S2
bit 3 = DEC S1
bit 4 = Horizon S2
bit 5 = Horizon S1
[[tcs:limit_logic|Limit Logic in TCS]]
MOTION Motion status bits
Args: N/A
Returns: this returns an 8 bit integer whose bits represent the following
bit0(LSB) = RA/AZ
bit1 = DEC/EL
bit2 = FOC
bit3 = DOME
bit4-8 = undefined
a 1 indicates axis in motion, 0 indicates no motion
PAD String describing hardware paddle button states Args: N/A Returns: any combination of the following charachers N = North S = South E = East W = West D = Drift (if not present, assume Guide) A characher is present if switch active, otherwise switch inactive
PADDRIFT Hardware paddle drift rate arcsec/sec Args: N/A Returns: -XXXXXXXXX.xxx
PADGUIDE Hardware paddle guide rate arcsec/sec Args: N/A Returns: -XXXXXXXXX.xxx
RA Right Assention Args: N/A Returns: [ddmmss.ss]
SECZ Air Mass Args: N/A Returns: [XXXXX.XX]
ST Sidereal Time Args: N/A Returns: [hh:mm:ss]
TIME Universal Time Args: N/A Returns: [HH:MM:SS]
VERIFY Verify that an RA/DEC position is within telescope limits Args: [RA] [DEC] [Epoch] RA=HH:MM:SS.ss DEC=DD:MM:SS.ss Epoch=EEEE.eeee Returns: 1 if coordinate is within limits
XALL "Extended ALL" Args: N/A Returns: [FOC] [DOME] [IIS] [PA] [UTD] [JD] FOC(focus pos) = +XXXXXX DOME(Dome Position) = -180 (always this value...) IIS(???) = -224.4 (always this value...) PA(Paralactic Angle) = -145.7 (always this value...) UTD(UT Date) = MM/DD/YYYY JD(Julian Date) = XXXXXXX.x
XDEC "Extended DEC" Args: N/A Returns: [COM] [NEXT] [REF] [OFF] [WOB] [DIFF] [BIAS] [GUIDE] [DRIFT] COM(Commanded Position) = +HH:MM:SS.ss NEXT(Next Position) = +HH:MM:SS.ss REF(Reference Position) = +HH:MM:SS.ss OFF(Offset Position) = +HH:MM:SS.ss WOB(Wobble) = +HH:MM:SS.ss DIFF(Difference) = +XXXXXXXXX.xxx BIAS(Bias Rate) = +XXXXXXXXX.xxx GUIDE(Guide Rate) = +XXXXXXXXX.xxx DRIFT(Drift Rate) = +XXXXXXXXX.xxx
XRA "Extended RA"
Args: N/A
Returns: [COM] [NEXT] [REF] [OFF] [WOB] [DIFF] [BIAS] [GUIDE] [DRIFT]
COM(Commanded Position) = HH:MM:SS.ss
NEXT(Next Position) = HH:MM:SS.ss
REF(Reference Position) = HH:MM:SS.ss
OFF(Offset Position) = +HH:MM:SS.ss
WOB(Wobble) = +HH:MM:SS.ss
DIFF(Difference) = +XXXXXXXXX.xxx
BIAS(Bias Rate) = +XXXXXXXXX.xxx
GUIDE(Guide Rate) = +XXXXXXXXX.xxx
DRIFT(Drift Rate) = +XXXXXXXXX.xxx
Satellite Requests
GETSATELAZ Satellite horizontal coordinates
Args: N/A
returns [EL] [AZ]
GETSATECI Satellite Earth Centered Inertial Cartesian coords
Args: N.A
Returns: [X] [Y] [Z]
GETSATECEF Satellite Earth Centered Earth Fixed Cartesian coords
Args: N.A
Returns: [X] [Y] [Z]
undefined Request
TEST1 ??? >> probably useless but is currently in the command set Args: ??? Returns: ???
INDEX ??? Args: ??? Returns: ???
PP ??? Args: ??? Returns: ???
SRVFRQ ??? Args: ??? Returns: ???
Dome Request
DOME Dome control information
Args: "PARAM" returns dome setup parameters, all other strings return control info
Returns:
Parameters: [CPD] [SD] [W] [SDW] [NU] [RHO] [PHI] [LOOK] [HOLD]
CPD(Counts Per Degree) = XXX.xxxxxxx
SD(Stow Degrees)= XXX.xxxxxxx
W(Dome Width) = XXX.xxxxxxx
SDW(Stow Dome Width)= XXX.xxxxxxx
NU = XXX.xxxxxxx
RHO = XXX.xxxxxxx
PHI = XXX.xxxxxxx
LOOK(Lookahead) = XX
HOLD(Hold Dome) = XX
Control Info: [DEL] [MOD] [INIT] [TELAZ] [AZ] [HOME]
DEL(Delta Position) = +XXX.XXXXXXX
MOD(Mode) = XX
INIT(Initialized) = XX
TELAZ(Telescope Azmouth) = +XXX.XXXXXXX
AZ(Dome Azmouth) = +XXX.XXXXXXX
HOME(Home Position) = +XXX.XXXXXXX
Focus Request
FOCSPEED Focus Speed Args: N/A Returns: ["FAST" or "SLOW"]
FOCUS Focus position Args: N/A Returns: +XXXXX
DIO Request
DIO All 6 bytes of DIO
Args: N/A
Returns: A1 B1 C1 A2 B2 C2 as hex numbers
A1:
Bit0: FOCUS UP
Bit1: FOCUS DN
Bit2: FOCUS F/S
Bit3: ESTOP STATUS
Bit4 HA ALT LIMIT
Bit5 DEC ALT LIMIT
Bit6 DEROT ALT LIMIT
Bit7 SPARE A7A
B1: Paddle Buttons
Bit0: NORTH
Bit1: SOUTH
Bit2: EAST
Bit3: WEST
Bit4: GUIDE/DRIFT
Bit5: SLEW
Bit6: DOME RIGHT
Bit7 DOME LEFT
C1:
Bit0: HA LIMIT
Bit1: DEC LIMIT
Bit2: HOR LIMIT
Bit3: HS NORTH
Bit4: HS EAST
Bit5: Dome Home
Bit6: Focus Up Limit
Bit7: Focus
A2:
Bit0: HA E SLEW
Bit1: HA W SLEW
Bit2: DEC N SLEW
Bit3: DEC S SLEW
Bit4 HOR SLEW LIMIT
Bit5 DEROT CW SLEW LIMIT
Bit6 DEROT CCW SLEW LIMIT
Bit7 REMOTE LOCKOUT
B2:
Bit0: HA DIR
Bit1: DEC DIR
Bit2: FOCUS DIR
Bit3: DEROT DIR
Bit4: HA INHIBIT
Bit5: DEC INHIBIT
Bit6: FOCUS INHIBIT
Bit7: DEROT INHIBIT
C2:
Bit0: RING BIT 0
Bit1: RING BIT 1
Bit2: SLEW PERMIT
Bit3: DEROT LIMIT
Bit4 DOME RIGHT OUT
Bit5 DOME LEFT OUT
Bit6 DOME ENABLE OUT
Bit7 SPAREC7B
Commands
ABERRATE Aberration corrections enable/disable Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
BIAS Bias enable/disable Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
BIASDEC DEC bias rate in arcseconds/second Args: [XXXXX.XX] Returns: "OK" or "FAILED"
BIASRA RA biasrate in arcsseconds/second Args: [XXXXX.XX] Returns: "OK" or "FAILED"
CANCEL Cancel current move Args: N/A Returns: "OK" or "FAILED"
CLEARDIFF Clear RA and DEC difference value Args: N/A Returns: N/A
DISABLE disable motion output Args: N/A Returns: "OK" or "FAILED"
DISEPOCH Set Epoch Args: XXXX.x Returns: "OK" or "FAILED"
DECLARE Initialize current position Args: "INITNEXT" to initialize "NEXT" position as current position "INITCOM" to initialize "COMMANDED" position as current position Returns: "OK" or "FAILED"
ELAZ Move to position in Elevation and Azmouth Args: [EE.EE] [AAA.AA] Returns: "OK" or "FAILED"
ENABLE enable motion output Args: N/A Returns: "OK" or "FAILED"
FLEX Flexure corrections enable/disable Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
LIMIT Limit override >> USE WITH EXTREME CAUTION!!!!! Args: "INHIBIT" will override limits, all other strings will enable limits Returns: "OK" or "FAILED"
MOVNEXT Move to NEXT position Args: N/A Returns: "OK" or "FAILED"
MOVOFF move to OFFSET position Args: N/A Returns: "OK" or "FAILED"
MOVRADEC Move to RA-DEC position Args: RA DEC EPOCH RAPM DECPM RA = HH:MM:SS.ss DEC = +DD:MM:SS.ss EPOCH = EEEE.eeee RAPM(RA Proper Motion) = XXXXX.xxx DECPM(DEC Proper Motion) = XXXXX.xxx Returns: "OK" or "FAILED"
MOVSTOW Move to stow position Args: N/A Returns: "OK" or "FAILED"
MOVWOB MOVWOB beam Args: ??? Returns: ???
NEXTPOS Set NEXT position Args: RA DEC EPOCH RAPM DECPM RA = HH:MM:SS.ss DEC = +DD:MM:SS.ss EPOCH = EEEE.eeee RAPM(RA Proper Motion) = XXXXX.xxx DECPM(DEC Proper Motion) = XXXXX.xxx Returns: "OK" or "FAILED"
NUTAT Nutation corrections enable/disable Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
PAD Software paddle command [Direction] [rate] or PAD XX for termination
This function is not recommended for use near the horizon limits!
Args: [Direction] [rate]
DIRECTION = NORTH, SOUTH, EAST, WEST, NE, NW, SE, SW
RATE = XXXXXXX.xx (arcsecs/sec)
any string not described in DIRECTION will terminate paddle
this terminate string must be sent at the end of each movement
when the button is released.
Returns: "OK" or "FAILED"
PADDLE Paddle enable/disable Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
PADDRIFT Paddle Drift rate in arcseconds/second Args: [XXXXX.XX] Returns: "OK" or "FAILED"
PADGUIDE Paddle Guide rate in arcseconds/second Args: [XXXXX.XX] Returns: "OK" or "FAILED"
PARALLAX Parallax corrections enable/disable Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
PARAM ??? Args: ??? Returns: ???
PRECES Precession corrections enable/disable Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
PROPMO Proper motion corrections enable/disable Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
REFPOS REFerence POSition (tod) Args: ??? Returns: ???
REFRAC Refraction corrections enable/disable Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
STEPDEC Move Declination XXXXX.XX arcseconds Args: [XXXXX.XX] Returns: "OK" or "FAILED"
STEPRA Move Right Assention XXXXX.XX arcseconds Args: [XXXXX.XX] Returns: "OK" or "FAILED"
TRACK Enable/Disable sidereal tracking Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED" WOBBLE WOBBLE -HH:MM:SS.ss -DD:MM:SS.ss Args: ??? Returns: ???
Catalogs Command
ABELL ABELL Catalog object XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
FK5 FK5 Catalog object XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
IC IC Catalog object XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
NGC NGC Catalog object XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
OKESTONE Okestone Catalog object XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED PPM PPM Catalog object XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
SAO SAO Catalog Object XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
YBSC YSBC Catalog Object XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
ZWICKY ZWICKY Catalog object XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
Planets Command
MERCURY Track Mercury Args: N/A Returns: "OK" or "FAILED"
VENUS Track Venus Args: N/A Returns: "OK" or "FAILED"
MARS Track Mars Args: N/A Returns: "OK" or "FAILED"
JUPITER Track Jupiter Args: N/A Returns: "OK" or "FAILED"
SATURN Track Saturn Args: N/A Returns: "OK" or "FAILED"
URANUS Track Uranus Args: N/A Returns: "OK" or "FAILED"
NEPTUNE Track Neptune Args: N/A Returns: "OK" or "FAILED"
PLUTO Track Pluto Args: N/A Returns: "OK" or "FAILED"
MOON Track Moon Args: N/A Returns: "OK" or "FAILED"
SUN Track Sun Args: N/A Returns: "OK" or "FAILED"
DOME Command dome control Args: This command takes one argument at a time from the following AUTO Autodome enable Args: ON = autodome on, any other = autodome off Returns: "OK" or "FAILED"
INIT Initialize dome Args: N/A Returns: "OK" or "FAILED"
STOW Stow dome Args: N/A Returns: "OK" or "FAILED"
LOOKAHEAD Lookahead enable Args: positive nonozero number=enable, any other = disable Returns: "OK" or "FAILED"
PARAM Set Dome Parameters Args: [CPD] [SD] [W] [SDW] [NU] [RHO] [PHI] [LOOK] [HOLD] CPD(Counts Per Degree) = XXX.xxxxxxx SD(Stow Degrees)= XXX.xxxxxxx W(Dome Width) = XXX.xxxxxxx SDW(Stow Dome Width)= XXX.xxxxxxx NU = XXX.xxxxxxx RHO = XXX.xxxxxxx PHI = XXX.xxxxxxx LOOK(Lookahead) = XX HOLD(Hold Dome) = XX Returns: "OK" or "FAILED"
PADDLE Control Paddle buttons Args: RIGHT = move right, LEFT = move left, any other= stop Returns: "OK" or "FAILED"
FOCUS move to absolute focus value XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
RELFOCUS relative move focus value XXXXXXX Args: XXXXXXX Returns: "OK" or "FAILED"
FOCZERO Zero current focus position Args: N/A Returns: "OK" or "FAILED"
FOCSTOP focus paddle stop Args: N/A Returns: "OK" or "FAILED"
FOCUP focus paddle up Args: N/A Returns: "OK" or "FAILED"
FOCDN focus paddle down Args: N/A Returns: "OK" or "FAILED"
FOCSPEED Set focus speed Args: "FAST" sets to fast, all other strings set speed slow Returns: "OK" or "FAILED"
Periodic Error Correction Request
PECSTAT Current PEC operation status Args: N/A Returns: [PEC_Condition] [PEC_Count] [PEC_Index] [PEC_Mode]
PECPROG Current PEC programming status Args: N/A Returns: [Percent_Done] [PEC_Correction]
Command
PECFILE Attempt to create a PEC file. Args: ??? Returns: ???
PEC Turn on PEC Args: "ON" = enable, any other string will disable Returns: "OK" or "FAILED"
Servo Request
CON ??? >> SERVO STUFF... NOT FOR NORMAL USE Args: ??? Returns: ???
SAMDATA ??? >> SERVO STUFF... NOT FOR NORMAL USE Args: ??? Returns: ??? SAMDONE ??? >> SERVO STUFF... NOT FOR NORMAL USE Args: ??? Returns: ???
SERVO ??? >> SERVO STUFF... NOT FOR NORMAL USE Args: ??? Returns: ???
Command
WCON axis, gd gp gi dmax vmax groot >> SERVO CONST... DO NOT MODIFY Args: ??? Returns: ???
SERVO ??? >> AXIS SERVO SAMPLING... DO NOT MODIFY Args: ??? Returns: ???
GD axis, value >> SERVO CONST... DO NOT MODIFY Args: ??? Returns: ???
GP axis, value >> SERVO CONST... DO NOT MODIFY Args: ??? Returns: ???
GPI axis, value >> SERVO CONST... DO NOT MODIFY Args: ??? Returns: ???
DMAX axis, value >> SERVO CONST... DO NOT MODIFY Args: ??? Returns: ???
VMAX axis, value >> SERVO CONST... DO NOT MODIFY Args: ??? Returns: ???
PERMAX axis, value >> SERVO CONST... DO NOT MODIFY Args: ??? Returns: ???
SAMPLE axis, interval, total samples >> AXIS SERVO SAMPLING... DO NOT MODIFY Args: ??? Returns: ???
DUMPSAM axis >> AXIS SERVO SAMPLING... DO NOT MODIFY Args: ??? Returns: ???
SAMSTART ??? >> AXIS SERVO SAMPLING... DO NOT MODIFY Args: ??? Returns: ???
SAMABORT ??? >> AXIS SERVO SAMPLING... DO NOT MODIFY Args: ??? Returns: ???
SYSSAVE ??? Args: ??? Returns: ???
SYSKILL Kills TCS process after disabling stopping all telescope motion.
Args: N/A
Returns: OK or Failure
SYSRESET Restarts TCS process after disbling the telescope Added by Scott 12/2012
Telescope should be stowed before doing this.
Args: [TIME] [DD/MM/YY] [HH:MM:SS]
If no arguments are used the TCS simply restarts
as if you had restarted the TCS computer. If for some reason
the time is bad on the TCS computer you can add the TIME
argument followed by the date and time in UT and TCS will
use this and not the computer time for astrometry.
Returns OK or Failure
TLE Gives TCS a new TLE for tracking Earth Satellites
Args: Follows this format exactly: [[https://en.wikipedia.org/wiki/Two-line_element_set]]
SATTRACK Tracks the current satellite TLE with the telescope.
Args: N/A
NEXTEVENT Gives you rise or set time in hours of coordinates set using the NEXTPOS command.
Args N.A
Returns: Rise/Set (0/1) state and time in decimal hours.
tcs/tcsng_command_list.1566668965.txt.gz · Last modified: 2019/08/24 10:49 by scott
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
