MOON

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
**Last updated: ~~LASTMOD~~**
----
======Cold Start Power Up Sequence======
//Procedure for coming out of lightning shutdown or checking out the telescope and instrument.//
----
=====Dome Part 1=====
  - Dome encoder cable over entry door
===West side of blue yoke, declination axis===
  - Dec encoder
  - Dec motor
  - Dec tac
===West side of base flange===
  - Finder scope lamp power (for reticle)
===East side of base flange===
  - Limit cable
  - Index sensor cable
===Inside the south pier===
  - From outlet box #5
    - Power cord running to power strip inside blue rack
    - Power cord running to power strip mounted to south pier
    - Power cord running to index meter box
  - Black rectangle cable connection laying inside
    - //NOTE: Two cables plugged into one another that have black connectors//
  - Index meter cable
    - //NOTE: Connects up underneath backside of index meter box//
===RA Axis===
  - RA encoder on west side
  - RA motor cable on east side
  - RA tachometer cable on east side
===Backside of blue rack===
  - Silver outlet box
    - Mux power plug
    - Bus extender cable
    - Bus BNC
  - Bus extender
    - Bus cable
      - //NOTE: There is a black screw keeping cable in place.//
  - Backside of dome box
    - #4 paddle
    - #2 bus extender cable
    - Dome encoder
    - DEC encoder cable
    - RA encoder cable
  - Backside of stepper box
    - Gate out BNC

----
=====Control Room=====
===Backside of blue control rack===
  - Bottom of rack
    - #5 TTL mono dome
    - #3 stepper motor control
    - #2 computer manual to dome and telescope control
    - #1 single paddle control to old paddle
  - FORTH computer backside
    - //NOTE: If 2MASS is on the telescope there should be nothing to connect.//
  - Silver outlet box
    - Bus BNC
    - Power supply cable
    - Power supply cable
===Backside of rack #1===
  - PC splitter box
    - "From dome" silver cable
  - Video monitor
    - Video input BNC cable
  - TV offset guide control backside
    - Round connector
  - Focus panel backside
    - Focus cable on left hand side
      - //NOTE: Easy to miss//
  - Chop box
    - Large round connector cable
    - Transducer BNC
===Backside of rack #2===
    - RA motor round connector
    - Temperature sensor square gray plug
      - //NOTE: Easy to miss//
===Backside of rack #3===
  - DEC motor cable
  - Master Control Panel backside
    - Slew SW BNC far left
    - J12 under cccc to the right
  - Telescope drive control backside
    - Limit cable p8
    - #5 TDC cable
    - Tilt meter cable
      - //NOTE: Easy to miss, just under DEC preamp//
    - #5 DEC preamp
    - #7 RA preamp
===Front of blue control panel===
  - Ribbon cable from port 5 to 5
===Front of rack #1===
  - Microphone connection for dome
===Behind control console===
  - Plug two cables running into ceiling
  - Plug power strip and UPS laying on the floor into the wall outlet
  - Plug two ethernets

----
=====Dome Part 2=====
===2MASS===
  - Plug in UPS into wall outlet.
  - Turn on UPS.
  - Plug in orange extension cord into UPS
  - Remove the cover form temperature control port.
  - While wearing a grounding strap, connect temperature controller cable.
  - Plug in temperature controller unit into UPS.
    - //NOTE: Sits on blue rack//
  - Plug in the Controller square gray power supply into power strip at base of telescope.
  - Plug in the IR Camera Power silver box into power strip at base of telescope.
  - Turn on Controller power supply
  - Turn on IR Camera power supply

----
===Follow the instructions in the UMINN 60"/2MASS binder to finish setup.===
MOON

User Tools

Site Tools

Page Tools
