public:kitt_peak:superlotis:superlotis_checkout
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
public:kitt_peak:superlotis:superlotis_checkout [2019/02/20 09:27] davner |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ---- | ||
| - | **NOTES FROM PETER MILNE**\\ \\ | ||
| - | I suggest that you have two pages viewable in your browser, this mtnops | ||
| - | page and the status page. For a remote person (like me), I can see from the | ||
| - | webcam and the status variables whether things are working. For a local person, | ||
| - | the webcam saves walking into the dome (unless you enjoy that little bit of | ||
| - | limbo). | ||
| - | mtnops page: | ||
| - | http:// | ||
| - | |||
| - | SL status page: | ||
| - | http:// | ||
| - | |||
| - | This DOES NOT have the camera take images. It powers the camera, but no | ||
| - | images. The reason for this is that eddy controls the camera, and at this point | ||
| - | I need to figure out the way to run that from a script on slotis. | ||
| - | |||
| - | Also, discussions are underway to set-up an override so the roof can be opened a | ||
| - | bit during the daytime. The script above only opens for 10 seconds and then sends | ||
| - | a stop, followed a minute later by a close....and it might only work when the | ||
| - | boltwood script is disabled. | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | //Peter Milne// | ||
| - | |||
| - | //Steward Observatory Phone : 520-626-5731// | ||
| - | |||
| - | //E-mail : pmilne@as.arizona.edu// | ||
| - | ---- | ||
| - | **TESTING SuperLOTIS AFTER SHUTDOWN**\\ | ||
| - | - Log into '' | ||
| - | - Log on as superuser by typing '' | ||
| - | - Type '' | ||
| - | - Open a browser, go to http:// | ||
| - | - The TCS block should be updating the local time and the TCS values should make sense. | ||
| - | - Look for UT or LST values that make no sense. | ||
| - | - The Weather Status should be regularly updating. The roof should show Closed and the Precip should show Not Raining. | ||
| - | - The System Temperatures should make sense. | ||
| - | - Check the Vacuum and Focus to make sure they do not show red (meaning out of bounds readings) | ||
| - | - The Camera Status value that is important is Camera Power, as the others do not update until the camera software runs its start-up (which is not part of this testing) | ||
| - | - Type '' | ||
| - | - That script will do the following in order: | ||
| - | - Flash the domelight on and off a few times (as a warning and tests commands) | ||
| - | - power the mount and camera and chiller | ||
| - | - Send movement commands (zenith, south ELAZ (30,180), west ELAZ (45,270), stow) | ||
| - | - Partially open roof, pause and then close roof | ||
| - | - Power down and kill scripts that were running | ||
| - | - Watch the webpage as these commands are executed. If onsite, you will hear some of these commands execute: | ||
| - | - The domelight should be obvious in the webcam as it turns on and off. | ||
| - | - The webpage should then show the MOUNT and CAMERA go from OFF to ON. | ||
| - | - The telescope should been seen to move to the positions in the webcam and the TCS values should display those moves. | ||
| - | - The telescope should return to stow. | ||
| - | - The roof should be seen to open slightly in the webcam. Then stop. Then close. | ||
| - | - The MOUNT and CAMERA power should turn off. | ||
| - | |||
| - | |||
| - | SuperLOTIS is good to go < | ||
| - | ---- | ||
public/kitt_peak/superlotis/superlotis_checkout.1550680078.txt.gz · Last modified: 2019/02/20 09:27 by davner
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
