Differences

This shows you the differences between two versions of the page.

--- public:catalinas:bigelow:kuiper_61:lightning_shutdown [2019/06/14 11:29]
mel
+++ public:catalinas:bigelow:kuiper_61:lightning_shutdown [2024/09/20 18:11] (current)
egreen
@@ Line 1: / Line 1: @@
 =====Lightning Shutdown=====
-  - Complete "End of Normal Night of Observing" shutdown
+  - Complete "End of Normal Night of Observing" procedures
   - In Dome
-    * Turn off all instrument electronics, including the camera shutter, and unplug two power strips and CCD power cord from orange plugs under the telescope.
+    * Turn off all instrument electronics (for M4K this would be the camera power supply, guider controller, Galil motor (for filter wheel and guider pickoff mirror), guider chiller, and shutter control box).
-    * On the west side, two power strips are now plugged into the two outlets.  Those are what need to be unplugged for lightning shutdown on this side
+    * Unplug the four (4) cords from the “clean” orange outlets on the underside of the telescope. The cords from the eastside outlets go to the camera power supply and guider controller, the cords from the westside outlets go to the two (2) power strips. NOTE: if M4K is not installed, configuration of power cords plugged into telescope may be different.
-    * If in use: shut down laptop computer, and unplug laptop from the orange UPS outlets located near the floor on the platform control console
+    * Shut down laptop computer (if in use) and unplug two (2) cords from the “clean” orange UPS outlets located near the floor on the platform control console.
-    * Turn off TCS computer using the light switch
+    * Turn off TCS by turning the red rotary switch on the side of the TCS junction box. NOTE: NEVER TURN OFF TCS UNLESS TELESCOPE IS IN STOW POSITION!
-    * Turn off telescope power
+    * Lower platform (if not already lowered).
-    * Lower platform
+    * Turn off telescope power and main power (note instructions on console regarding order of switches).
-    * Turn off main power
   - In Control room
-    * On BIGAUX double click "shutdown bigpop", and click "shutdown bigpop" when prompted.  You will need to enter the username "bigobs" and the Gerard password.
+    * Shut down computers BigAux, BigCCD, Gerard, and BigGuider via their respective sutdown icons on their monitors.
-    * Manually shutdown all computers.
+    * Shut down BigPop computer and Telcom Server via button or switch on front of their panels.
-      * Gerard
-      * BIGCCD
-      * Bigguider
-      * BIGAUX
     * Turn off printer.
-    * Turn off Telcom server
+    * Unplug all power cords marked with red tape from orange outlets on wall behind the computer monitors.
-    * Turn off and unplug power strip on west wall.
+    * Turn off CSS surge strip at back of table by the door and unplug surge strip cord from orange outlet below (if not already done).
-    * Unplug printer relay.
+  - In UPS room
-    * Unplug everything from orange outlets behind observer work station, as well as UPS outlets by the video finder scope monitor
+    * Turn off vertical yellow power strip to the right of Brandywine.
-    * Unplug computer racks (plugged into orange outlet #4 on wall below emergency stop)
+    * Unplug GPS (Brandywine) and yellow power strip cords from “clean” (orange) power outlet (both are marked with red tape).
-  - In UPS Room, unplug:
+    * Unplug Trendnet (small white box w/red tape and grey network cable attached) from “dirty” (regular) power outlet (NOTE: Trendnet MUST be plugged into a “dirty” power outlet when coming out of lightning shutdown).
-    * The emergency stop plug (bright yellow) no longer needs to be unplugged when going into lightning shutdown.
+    * Unplug any cords plugged into the orange outlets above the UPS, in particular the CSS rack cord (marked with red tape)
-    * GPS
+    * Follow separate instructions for UPS shutdown posted on UPS room wall.
-    * Shutdown UPS following instructions posted on board.

MOON

User Tools

Site Tools

Differences

Page Tools