MOON

User Tools

Site Tools

Trace:
phd2:phd2_guiding

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
phd2:phd2_guiding [2018/10/03 17:41]
paul 		phd2:phd2_guiding [2019/04/25 20:59] (current)
scott
Line 9: Line 9:
 (*) When using VATT4k and GUFI, these motors move the two filter wheels for the science camera, the guider camera's filter wheel, the guider camera's 3-axis translation stage, and the stage carrying the center mirror and the U mirror. (*) When using VATT4k and GUFI, these motors move the two filter wheels for the science camera, the guider camera's filter wheel, the guider camera's 3-axis translation stage, and the stage carrying the center mirror and the U mirror.
  
-  * start indiserver and correct drivers+  * start indiserver
     * click the indiserver icon on the desktop     * click the indiserver icon on the desktop
     * (a terminal window should appear)     * (a terminal window should appear)
Line 18: Line 18:
     - in the ''Main tool bar'', click icon that looks like a usb male connector     - in the ''Main tool bar'', click icon that looks like a usb male connector
        * (''connect equipment'' window should appear)        * (''connect equipment'' window should appear)
-    - in ''connect equipment'' window:   +    - in ''connect equipment'' window verify the following settings:   
-       * select camera type "INDI Camera",  +       * equipment profile "vatt imagers" or "vatt spec" depending on your instrument (the imagers are 4k CCD and GUFI), 
-       * select mount type "INDI Mount",  +       * camera type "INDI Camera",  
-       * select aux type "None"+       * mount type "INDI Mount",  
 +       * aux type "None"
     - in ''connect equipment'' window, in the camera row, click on the icon that looks   like a screwdriver and wrench in an "X"     - in ''connect equipment'' window, in the camera row, click on the icon that looks   like a screwdriver and wrench in an "X"
        * (''INDI Configuration'' window should appear)        * (''INDI Configuration'' window should appear)
-    - in ''INDI Configuration'' window check following settings:+    - in ''INDI Configuration'' window verify the following settings:
       * Hostname: localhost       * Hostname: localhost
       * port: 7600       * port: 7600
Line 32: Line 33:
       * (''INDI options'' window should appear)       * (''INDI options'' window should appear)
     - select the ''Apogee CCD'' tab     - select the ''Apogee CCD'' tab
-    - check following settings: +    - verify the following settings: 
-      * in the port section click the ''network'' button+      * in the port section ''network'' is selected
       * in the network section:       * in the network section:
-      * subnet: 10.0.255.255 +          * subnet: 10.0.255.255 
-      * ip:port : 10.0.3.14:2571+          * **Note the 4K guider is currently being repaired . We are using the VATTspec guider for all guiding. In practice this means the ip:port will be 10.0.3.12:2571** 
 +          * <del>offset guider (used with imagers) ip:port : 10.0.3.14:2571; slit plate guider (used with VATTspec): 10.0.3.12:2571</del> 
     - click the ''connect'' button in the ''Connection'' field     - click the ''connect'' button in the ''Connection'' field
-      * (after a few seconds, a bunch of new fields and tabs should appear.)  +      * (after a few seconds, a bunch of new fields and tabs should appear)   
 +      * (The message "[ERROR] Model is not supported by the INDI Apogee driver" may mean that the camera is not powered up.)
     - near the bottom of the window, turn on the cooler     - near the bottom of the window, turn on the cooler
     - IF YOU ARE GOING TO BE AUTOGUIDING:     - IF YOU ARE GOING TO BE AUTOGUIDING:
Line 47: Line 51:
     - click OK in the ''INDI Configuration'' window     - click OK in the ''INDI Configuration'' window
     - click ''Connect'' in the ''Connect Equipment'' window, in the camera section     - click ''Connect'' in the ''Connect Equipment'' window, in the camera section
-    - the button should now say ''Disconnect''+          * (the button should now say ''Disconnect'') 
 +    - IF YOU ARE GOING TO BE AUTOGUIDING: 
 +          * in ''INDI Configuration'' window verify the following settings: 
 +              * Hostname: localhost 
 +              * port: 7600 
 +              * driver: VATT-GUIDE-INDI 
 +              * Port: [empty] 
 +          * exit the INDI Configuration window 
 +          * click ''Connect'' in the ''Connect Equipment'' window, in the mount section 
 +          * (the button should now say ''Disconnect'')
     - click ''Close'' in the ''Connect Equipment'' window     - click ''Close'' in the ''Connect Equipment'' window
     - In the ''Main tool bar'' (it may be positioned anywhere in the window),      - In the ''Main tool bar'' (it may be positioned anywhere in the window), 
Line 66: Line 79:
       * The Dark Library is located in the directory ''/home/vattobs/.phd2/''.       * The Dark Library is located in the directory ''/home/vattobs/.phd2/''.
       * The directory ''/home/vattobs/PHD2/PHD2_CameraFrames...'' is automatically created for the session.       * The directory ''/home/vattobs/PHD2/PHD2_CameraFrames...'' is automatically created for the session.
-      * If you need to capture more than 100 images, make a renamed copy of the session directory; new   //fits// files should start populating the original session directory.+      * If you need to capture more than 100 images, make a renamed copy of the session directory; new   //fits// files should start populating the original sesson directory.
   * Start Imaging   * Start Imaging
     - in the bottom left of the PHD2 window there is a button with 2 arrows forming a circle. Click that button.     - in the bottom left of the PHD2 window there is a button with 2 arrows forming a circle. Click that button.
     - the button should gray out, the stop sign button should turn red, and images should start appearing     - the button should gray out, the stop sign button should turn red, and images should start appearing
 +  * Start Guiding
 +    - change the exposure time setting and contrast slider to find an appropriate guide star.
 +    - Click on the guide star
 +    - click on the circular icon i the tool bar that looks like a target
 +
 +
 +  Offset Guider Stage
 +
 +Note: All numbers are GUI units. The travel limits are accurate but the diagram is only an approximation.
 +{{ :phd2:offset_guider_stage_2.gif?direct |}}
 +
phd2/phd2_guiding.1538613686.txt.gz · Last modified: 2018/10/03 17:41 by paul

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki