User Tools

Site Tools


vatt:vatt_stall

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
vatt:vatt_stall [2021/06/15 04:22]
paul
vatt:vatt_stall [2021/06/17 22:46]
paul
Line 1: Line 1:
 ====== Recovering from a Stall ====== ====== Recovering from a Stall ======
  
-^ ^Jun 14, 2021, P Gabor et al.^ ✔✘ ^  +^ ^Jun 14, 2021, P Gabor et al.^^ ✔✘ ^  
-|Control room | :!: Mirror cover must be open. :!:  | | +|Control room | :!: Mirror cover must be open. :!:  || | 
-|Control room | 8-) If you want to close the dome slit (may be a good idea in very cold weather), close the mirror cover (assuming that the **breaks came on** when the stall occurred), than close the dome slit, and then open the mirror cover again. | | +|Control room | 8-) If you want to close the dome slit (may be a good idea esp. when windy), close the mirror cover (assuming that the **breaks came on** when the stall occurred), than close the dome slit, and then open the mirror cover again. || | 
-|Control room |Turn on the dome floodlights | | +|Control room |Turn on the dome floodlights || | 
-|Control room |''Breaks off''  :!: **Be ready to set the breaks again** if the telescope slumps in elevation when the breaks are released (watch the telescope in cameras, and watch the elevation value in TCSglue) | | +|Control room |''Breaks off''  :!: **Be ready to set the breaks again** if the telescope slumps in elevation when the breaks are released (watch the telescope in cameras, 8-O and watch the elevation value in TCSglue) || | 
-|Control room |Keep dome tracking on | | +|Control room |Keep dome tracking on || | 
-|Dome, lower lvl |Inspect the "flippers" and find the double-headed bumper. You will need to spin the telescope back to its stow azimuth. Remember that | | +|Dome, lower lvl |Inspect the "flippers" and find the double-headed bumper. You will need to spin the telescope back to its stow azimuth. Remember that: || | 
-| ::: |=) the double-headed bumper "lives" in the South | ::: | +| ::: |=) the double-headed bumper "lives" in the South || ::: | 
-| ::: |=) from your vantage point at the dome's lower level, a flipper may show a green patch or no patch; you can never see a red patch from there | ::: | +| ::: |=) from your vantage point at the dome's lower level, a flipper may show a green patch or no patch; you can never see a red patch from there || ::: | 
-| ::: |=) if both are green, simply align the arrows **within a few inches** | | +| ::: ^ Safe (recommended) ^ Less safe | ::: | 
-| ::: |=) if one is green and the other has no patch, spin towards the latter, flipping it to green; then keep spinning until the arrows align **within a few inches** | ::: | +| ::: |=) if both are green, simply align the arrows meticulously |if both are green, simply align the arrows **within a few inches**  | | 
-|Dome, upper lvl |Step onto the telescope yoke platform carefully (avoid imparting angular momentum in azimuth), and move the telescope to zenith | | +| ::: |=) if one is green and the other has no patch, spin towards the latter, flipping it to green; then keep spinning until the arrows align perfectly |if one is green and the other has no patch, spin towards the latter, flipping it to green; then keep spinning until the arrows align **within a few inches** | ::: 
-|Dome, lower lvl |Align the arrows **accurately** | |  +|Basement |__Disable the hydtrostatic bearing:__ Turn ''Stage 2'' off. |//Does not apply// | 
-|Dome, upper lvl |Bring the dome to its home position (gently spinning the encoder wheel) | | +|Dome, upper lvl |Move the telescope to zenith |Step onto the telescope yoke platform carefully (avoid imparting angular momentum in azimuth), and move the telescope to zenith | | 
-|Control room |Set the breaks | | +|Dome, upper lvl |Turn the derotator (considerable force is required) back to home, untwisting the cable bundle  |Still standing on the yoke platform, turn the derotator (considerable force is required) back to home, untwisting the cable bundle | | 
-|Control room |Close the mirror cover | | +|Dome, lower lvl |Align the Azimuth arrows **accurately** | |  
-|Control room |Turn Thermal control off | | +|Dome, upper lvl |Bring the dome to its home position (gently spinning the encoder wheel) || | 
-|Control room |Stop ''Autocollimation'' | | +|Basement |__Enable the hydrostatic bearing:__ Turn ''Stage 2'' on. |//Does not apply// | | 
-|TCS room |[[vatt:vatt_reboot_vatttel|Reboot VATTtel]] | | +|Control room |Set the breaks || | 
-|Control room |Start ''Autocollimation'' | | +|Control room |Close the mirror cover || | 
-|Control room |Close and open ''TCSglue'' | | +|Control room |Turn Thermal control off || | 
-|Control room |Turn Thermal control on | | +|Control room |Stop ''Autocollimation'' || | 
-| ^Done! | |+|TCS room |[[vatt:vatt_reboot_vatttel|Reboot VATTtel]] || | 
 +|Control room |Close and open ''TCSglue'' || | 
 +|Control room |Start ''Autocollimation'' || | 
 +|Control room |Turn Thermal control on || | 
 +| ^Done! || |
vatt/vatt_stall.txt · Last modified: 2021/06/17 22:46 by paul